Duolabs Cas Interface 3 Plus USB "NEW"

Description:�� ��Yet again Duolabs strike back with another ground breaking device. The Cas Interface 3 (discontinued) and Cas Interface 3 +Plus (from 2006). In a single product, the CAS Interface 3, combines all the superb features of the CAS Interface 2, its Add-On Board plus many additional options. This new release offers very advanced technical features. Unlike the CAS Interface 2, the CAS Interface 3 can fully manage PCMCIA connectors and easily connect external additional modules. However, the most interesting feature is the possibility of being able to emulate the PCMCIA port of a Common Interface (EN50221) receiver and thus use a Cam directly as if it were inserted in a receiver. Consequently the CAS Interface 3 can also be used by professionals to test a CAM (Conditional Access Module) without inserting it in a receiver. CAS Interface 3 also enables users to manage and program several types of SmartCard, which includes both current ones and those yet to be developed. Therefore the CAS Interface 3 can be regarded as a multifunction programmer suitable for the management of J-Tag, ISP, I2C, etc., through a USB port. �� The Kit supplied with CAS Interface 3 comprises of: ��� 1 CAS Interface 3 +Plus ��� 1 20-Pin female cable, length 30 cm ��� 1 J-Card ��� 1 Dummy Card Technical Information: The main features of this great device are as follows: ��� USB Full Speed connection at 12 Mbit��� RS-232 Serial Connection��� 20 Pin External Connector��� Internal Clock Speed 48Mhz��� No need for external power supply��� Full PCMCIA connector support��� Full support for next generation Wireless devices��� CAS Studio user friendly GUI ��� On the ground features: Supported Common Access Modules (CAM): ��� Diablo CAM. Cas Interface 3 together with Cas Interface 2 are the only programmers which are supporting the Diablo CAM Light, Diablo CAM Wireless and Diablo CAM WiFi programming. The programming for this device is very quick and reliable. Simply insert the CAM in the Cas Interface and choose the file you want to load in. ��� Magic Cam, Matrix Cam, Matrix Revolution, Matrix Reloaded, Matrix Reborn, and all CAMs based on SIDSA chipsets, which can be managed directly by means of a PCMCIA connector. For a full list of supported modules, open the Graphics Menu of Cas Studio. Remember to download the latest release from our web site. Thanks to the High Speed internal clock Cas Interface 3 is around 4 times faster than Cas Interface 2. Most of software routines for Flash writing have been rewritten. ��� Joker Cam, Zeta Cam and substantially all CAM modules based on NEOTION chipsets. These modules can be programmed and repaired using a J-Card. For a full list of supported modules, open the Graphics Menu of Cas Studio. Remember to download the latest release from www.duolabs.com. ��� Dragon Cam. It is possible to program any version by inserting the Dragon Cam into Cas Interface 3 and using a Dummy Card. This mode eliminates the need of inserting the Dragon Cam into a receiver, which can sometimes damage the CAMs besides being unpractical. It is also possible to repair faulty Dragon Cams if they fail to initialize due to a faulty Flash Memory. To do so, it is sufficient to open the module and connect a few wires, following a procedure that can be easily implemented even by less expert users. Special thanks goes to Dream Multimedia for their support and patience. ��� X-Cam, with ANGEL and ORION chipsets, standard and premium version. It is possible to program any version by inserting the X-Cam into Cas Interface 3 and using a Dummy Card. This mode eliminates the need of inserting the X-Cam into the receiver, which can sometimes damage the CAMs besides being unpractical. It is also possible to repair faulty X-Cams if they fail to initialize due to a faulty Flash Memory. In this case it is necessary to open the module and connect a few wires, following a procedure that can be easily implemented even by less expert users. Special thanks goes to X-Crypt for their support. ��� GigaCAM with Smit chipsets. This is one of the most recent adds to the CAM programming. Smartcard support. ��� Smartcard programming. This feature is very important for all those who wants to program a Smartcard based on PIC microcontroller or Atmel microcontroller. The full list of Smartcard can be viewed directly from the graphical menu of Cas Studio. More... All the OS based cards like Titanium Card, OPOS Card, Knotcard and more can be programmed without any problem throught the USB port. All future Smartcard can be supported thanks to the great flexibility of Cas Interface 3.Dragon Card Loader can be fixed if corrupted by the special repair function. ��� RS-232 Phoenix Smartmouse emulation. This emulation can be done through the RS-232 serial port. No matter what's the clock speed for the Smartcard. You can either choose 3,58/3,68/4,00/6,00 Mhz. This great feature is given by the total flexibility of the internal programmable clock generator. ��� D
Azi 330,3 LEI
Cumpără la cel mai bun preț de la magazinele de mai jos sau caută alte produse:
Cere părerea prietenilor tăi: